Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Parts & Accessories

Stan's NoTubes Neo Hub Spring and Pawl Kit
$9.00
Replacement springs and pawls. Includes 6 pawls, 6 springs and 1 plastic retaining ring that holds the pawls in place even during disassembly to ensure you're never searching the floor for tiny springs.
Stan's NoTubes Rim Tape
$11.25 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
Stan's NoTubes Neo Bearing Kit
$12.50
Replacement bearings for Stan's NoTubes Neo hubs. Includes 2 bearings. - 26mm OD x 15mm ID - 7mm thick
Stan's NoTubes Spoke Powder Assembly Compound
$13.00
The same spoke thread treatment used by Stan's pro wheel builders is now available to everyone. Stan's SRD Spoke Powder fills the threads of the spoke and functions as both a lubricant during assembly and a thread lock once built. Each bottle contains 24g (.8oz) which will treat approximately 300 wheels. The PTFE powder in Stan's SRD Spoke Powder acts as a barrier, keeping the metal of the nipple from bonding to the metal of the spoke and preventing spoke wind up during build or adjustment. In promoting a smoother turning nipple, the powder also ensures more accurate and consistent wheel builds, with less “ping and pop" during and after the build. The powder also fills the threads of the spoke to act as a thread lock that prevents loosening and de-tensioning and is particularly well suited for mechanically locking nipples such as Sapim's Secure Lock. - Improves tension consistency and overall build quality - Prevents spoke wind up - Offers secure thread lock between spoke and nipple - Prevents corrosion between spoke and nipple - Can be used dry or as a slurry - Works great with mechanically locking nipples
Stan's NoTubes 3.30/3.30Ti Hub Kit
$15.00 - $20.00
Stan's 3.30/3.30Ti Hub Kit converts Stan's 3.30 front hubs from quick-release to through-axle compatible. Installation is easy—just pull the old ones off and put the new ones on. Conversion kits available in 12mm and 15mm.
Stan's NoTubes Tubeless Valve Stems
$16.00
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
Stan's NoTubes Universal Schrader Tubeless Valve Stems 32mm
$16.00
Compatible with straight valve hole Hugo 52 rims and designed to fit 7.5 - 8.5mm valve holes. Sold as a pair. Identifying your Hugo rim and selecting the correct valve stem: Stepped Hugo rims have a larger diameter valve hole on the interior of the rim, and a narrower hole on outside of the rim. Quick tip: don't remove your tire if you don't have to. If your Hugo rim decal reads: MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this valve. For "Stepped" valve hole Hugo use part AS0105 - Valve Stem pair, Schrader, 32mm, 14mm base.
Stan's NoTubes Neo Front Hub End Caps
$20.00 - $21.00
Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place
Stan's NoTubes Neo Rear Hub End Caps
$20.00 - $23.00
Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs - SealLock end caps feature a low friction U-cup seal that snaps into place
Stan's NoTubes Downhill Rim Strip
$22.50
Stan's Downhill Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!
Stan's NoTubes Olympic Rim Strip
$22.50
Stan's Olympic Rim Strip converts Stan's rims to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!
Stan's NoTubes Alloy Tubeless Valve Stems
$23.00
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
Stan's NoTubes 3.30 Shimano/SRAM Freehub Body (9/10-speed)
$74.00
Replacement Shimano/SRAM freehub body for Stan's NoTubes 3.30 rear hubs.
Stan's NoTubes Neo Durasync Freehub
$80.00
Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components
Stan's NoTubes XD Freehub Conversion Kit (Stan's 3.30 Hubs)
$80.00
This conversion kit allows you to use SRAM's 11-speed mountain cassette on your Stan's NoTubes wheels. Each kit includes an XD freehub, spacer, drive side end cap, and three sealed bearings.
Stan's NoTubes Neo Speedsync Freehub
$130.00
Stan's original Neo hub has evolved to be stronger and more reliable than ever. The additional stress of larger cassette cogs, more capable bikes, and even more challenging trails led to the creation of the Neo with Speedsync. This CNC machined Speedsync freehub is a direct replacement for your Neo hub and includes pawls, springs, pawl retaining ring, and 2 red freehub spacers. Bearings are pre-installed. Note: - Singlespeed freehub cannot be used to convert a hub originally set up with a Shimano or Sram XD freehub to SS. This freehub is only to be used with Stan's Neo SS hubs. - OneUp freehub WILL NOT WORK with a SRAM cassette or Shimano cassette without a One Up Shark Cluster.
Spank Fratelli Tubeless Ready Tape
$11.90
SPANK Industries Fratelli Tape is a special ultra-light polyamide, adhesive tubeless conversion tape, which is ideal for SPANK's patented OohBah profile rims. Thicker, less pliable tapes are often difficult or impossible when taping complex rim profiles. Fratelli tape makes tubeless set up simple, and adapts well to a variety of rim types, including sleeved and welded joints. 25mm width tape is suggested for rims up to 29mm internal width, and 30mm tape for rims 30mm internal width and greater. With adhesive properties unaffected in a wide temperature range, Fratelli tape is also perfect for winter riders, or those in exceptionally hot environments. - Material: Ultra Thin Polyamide - Width: 25mm or 30mm - Features: high temperature range adhesive, ideal for complex rim profile Installation: - Affix tape all the way around on the right side snug against the bead hook - Then repeat a second circumference around the left side, providing double-thick coverage over the spoke holes - Use a red-hot awl or similar to pierce the valve hole
Spank Oozy/Spike Rear Hub Adaptors
$19.90
Hub Adapters for all Oozy hubs and 2016 Spike hubs.
Spank Spike DH Rear Hub Adaptor
$19.90
Converts SPIKE DH R150 Rear Hubs to 12x157mm. Compatible only with SPIKE and SPOON (150mm) wheels produced in 2015 or later (with SPIKE hubs). - Material : Alloy - Weight (g): ±14 - Compatibility : SPIKE DH 12x150mm Rear Hubs
Spank Spoon 135/150 Freehub Bodies
$69.90
These freehub bodies fit only the older Spoon hubs, not compatible with the new Oozy or Spike hubs.
Spank Oozy/Spike Freehub Bodies
$95.00
Replacement cassette bodies for Oozy hubs and Spike hubs. - Shimano or SRAM - Alloy or Steel
Saris Trainer Skewer
$14.99
- Replacement rear wheel skewer. - Specifically designed for use with Saris trainers. - Can be used for both indoor and outdoor rides.
Salsa QR Skewer Springs
$6.00
Salsa springs for Flip-Off skewers
Salsa Fat Conversion Hub End Caps for Front (150mm)
$25.00
- Converts Salsa Conversion hubs from 135/142 to 150mm in order to use with the RockShox Bluto Fork, or other 150 mm Thru-axle forks - Requires the wheel to be re-dished
Salsa Front Stainless Flip-Off Skewer
$32.00
Salsa's Stainless Flip-Offs use stainless steel rods for corrosion-resistant strength. They're strong, lightweight, and gorgeous. - Recommended for front rigid fork or full suspension use - Beautifully machined and hand friendly - Variety of sizes, sold as pairs or individually, front or rear - Black, Silver, Blue, Red, Green, Orange, Purple, or Pewter - More than just eye candy, they’re hand candy, as well - Weight: 49g
Salsa Front Titanium Flip-Off Skewer
$36.00
Salsa's Ti Flip-Offs are as beautiful to the touch as they are to the eye. Lightweight. Smooth. Recommended for road use or rigid front mountain bike use only. Available in a whole host of colors. - Beautifully machined and hand-friendly - Black, Silver, Blue, Red, Green, Orange, Purple, or Pewter - More than just eye candy, they’re hand candy, as well - Weight: 40g
Salsa Rear Stainless Flip-Off Skewer
$36.00
- Standard skewers fit either 130 or 135mm spaced hubs, unless listed as another length (i.e. 170mm) - 6061 machined lever with stainless steel pivot and laser-etched logo - All shafts are 5mm in diameter
Salsa Deadbolt Ultralight Thru-Axle
$39.00
The Deadbolt Ultralight Thru-Axles are offered in a 6mm flat button head design, for a flush, clean look. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications - 6mm hex wrench required for installation
Salsa Rear Titanium Flip-Off Skewer
$40.00
Salsa's Ti Flip-Offs are as beautiful to the touch as they are to the eye. Lightweight. Smooth. Recommended for road use or rigid front mountain bike use only. Available in a whole host of colors. - Beautifully machined and hand-friendly - Black, Silver, Blue, Red, Green, Orange, Purple, or Pewter - More than just eye candy, they’re hand candy, as well - Weight: 44g
Salsa Deadbolt Thru-Axle
$49.00
The Deadbolt Thru-Axles feature the classic-looking Salsa lever and can be adjusted to return to the desired position when properly tightened. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications